CRAFT DISTILLING - VANILLA COFFEE RUM

ageing, craft, distilling, rum, t500 -

CRAFT DISTILLING - VANILLA COFFEE RUM

The celebration of craft distilling continues throughout May as we approach World Whiskey Day. Now that we have established the basics of craft distilling with the T500 and the Alembic Pot Still attachment, let’s try a great recipe to put it into practice! The first in this series is our vanilla coffee rum which can be had neat or in your favourite cocktail.

Rum:  Rum is produced from the distillation after fermentation of sugar cane/ beet products like molasses, sugar cane syrup and or other sugar cane products

THE WASH

In my stainless steel fermenter, I added 4kg of molasses and 1kg of brown sugar along with 5L of hot water. I then stirred the lot ensuring it was completely dissolved and then topped up to 23L with water. Be sure to use a food grade molasses, that is doesn’t contain added sulphates, because while the copper Alembic dome will remove most of these, it is more hassle.

My fermenter now filled with 23L of wash was cooled to pitching temp then added 3 packets mangrove jacks strong ale yeast and allowed to ferment under room temperatures for three weeks.  The reason I used this yeast was that it was on hand and I wanted to see if there was any difference compared to my normal method of using distillers yeast.

OG: 1.078             FG: 1.008              ABV: 9.19%

The day before I was planning to distil I degassed the wash by stirring it vigorously and then added part A of the still spirits turbo clear, stirred and waited an hour then added part B gently stirring to top of the wash and allowed to sit for 24 hours.

Tip: move the fermenter at this point into the easiest place possible so that when transferring the wash the fermenter doesn’t need to be moved and potentially disturbing the yeast on the bottom of the fermenter.

The next day I used the tap on the fermenter and a hose to run the wash into the T500, added 5 capfuls of conditioner, boiling chips and set up the alembic.

STRIPPING RUN

Once the alembic dome was set up with my collection 5L vessel ready, I turned on the water and adjusted the water flow to just over 2.5L per min then turned off the water and turned on the T500. I set the temperature to 1000C and started heating, by holding down the heating button I then adjusted the power level to 65% power. This does make the process take a bit longer, but I find the product noticeably better. Once the temperature on the alembic reaches 400C I turn on the water and check that it is still running at just over 2.5L per min.

For this run, we collect all the spirit which will start at about 65% ABV and will slowly progress down to 30% ABV where I like to turn off the T500, but I find the quality starts to deteriorate rapidly.

By this point, I had 4L of 60% spirit, and it was Friday afternoon, so I turned off the water and T500 sealed up my collection vessel to deal with on Monday.

SPIRIT RUN

After cleaning out the T500, I added the spirits the boiling chips back in and topped up the T500 to 10L with filtered water. I filled my botanicals basket with 30g fresh coffee beans and three vanilla pods. Once the alembic dome was set up with five 200ml collection vessels and  5L vessel, I turned on the water and adjusted the water flow to just over 2.5L per min then turned off the water and turned on the T500. I set the temperature to boil and started heating, use a water flow regulator to help. 

FORESHOTS

Once the temperature probe reaches 55°C (131°F) turn on the cold tap water. When the distillate begins to come out, you can collect the foreshots which are the more harmful components of the heads and is typically the first 200 ml (6.8 US fl oz). This section contains the most harmful compounds present in the wash and should be discarded. NOTE: the foreshots section is 200 ml (6.8 US fl oz) per stripping run distillate.

HEADS

After the foreshots are over you will be entering the heads section of distilling. This contains a lot of the lower boiling point components as well as ethanol. Collect these into separate small containers, and once distilling is complete decide whether they are suitable for the final Rum or not when blending the heads and tails into the hearts section. Start collecting the heads in separate containers with a volume of around 150 ml (5 US fl oz), putting them to the side once full. Label each filled cup with a number in the order it comes out of the still, e.g. 1 for the first cup, 2 for the second cup and so on. Once the temperature reaches around 83-85°C (181 – 185°F) the heads section is complete, and it is time to start collecting the hearts. - The volume of these containers varies depending on the volume of liquid for the spirit run and personal preference. A good guideline is around 150 ml (5 US fl oz)/stripping run. This gives a good balance between ease of distilling and ability to blend well later on.

HEARTS

Place a larger vessel under the output tube and start collecting all of the hearts in the one vessel. This middle part is good spirit so does not need to be separated into containers. Continue collecting the hearts until the spirit is coming out at around 55% ABV. Once the still temperature reaches 90°C (194°F) the heart section is complete, and it is time to collect the tails. The hearts collected in the 9 middle of the spirit run are the best part of the spirit and will form the base for which to blend with after distilling is complete. TAILS Start collecting the tails in separate containers, putting them to the side once full, just as was done when collecting the heads of the spirit. Label each filled cup with a number in the order it comes out of the still (like for the heads). Once the still temperature is around 93-95°C (199 – 203°F), the tails collection is complete. At this temperature, the good part of the tails has all been collected. It is now time to start collecting the ends of the tails. Place a larger vessel under the still and collect the last of the tails in a larger vessel until the temperature is around 98°C (208°F) or the output is below 20% ABV, then turn off the boiler and disconnect it from the power outlet. This last part of the tails is not used in final spirit but can be kept to increase the yield for future stripping runs. Wait for the boiler contents to cool to a safe temperature before discarding the contents. Clean the boiler, dome top and condenser thoroughly and rinse well.

BLENDING

What you have collected is the heads, the hearts, the tails, and the final of the tails. The heads and tails are both in multiple separate containers while the hearts are in one large container. The reason you have collected the heads and tails in small sample fractions is that not all of the heads and tails will be good to use and mix in with the hearts. Normally the last few cups of the heads (closest to the hearts), and the first few cups of the tails (closest to the hearts) will be good to add in with the hearts, but you will need to taste each sample container and choose what you want to add into your mix. By collecting these heads and tails in separate fractions, less emphasis has been placed on when to make the heads and tails cuts during the distilling. Work your way through tasting and smelling each of the heads and tails fractions and add each container you are happy with to your hearts container. You do not necessarily have to add the entire container. The heads of the spirit generally add the harsher flavours to the spirit but contain a large percentage of ethanol, whereas the tails contain a lot of the flavours but a small percentage of ethanol. Add any fraction samples from the heads and tails that you are not happy with to the second large container with the final part of the tails. This large tails container, called the ‘feints’, is not necessarily bad but it has not been refined enough yet to use in the final spirit. This should be saved and can be added to the next stripping run you do with your next batch of Rum so that 10 ALCHEMIST it is not all wasted. Alternatively, these feints can be collected from multiple Rum batches and when you have enough, doing a spirit run of all feints can lead to a delicious Rum.

AGEING

Dilute your final collected spirits you are happy with down to 50% ABV with filtered or distilled water in a large 5 L (1.3 US Gal) glass jar or demijohn, use an alcoholmeter, hydrometer or refractometer to measure the ABV. There are water calculators online to aid in dilution. Make sure your jar is large enough and still has more space as you will be required to add more water to this jar as the ageing process progresses. Add some Charred American Oak Infusion spirals to your Rum as per the instructions on the spirals and leave it in a cold, dark area for the ageing process. The flavour will begin to extract from the spirals instantly, and after 2 weeks this flavour will be completely extracted. Taste the Rum periodically during the ageing process, the spirals can be removed at any time as to your preferred taste. Leave the spirits to age for 3 weeks in a cool dark place. After 3 weeks dilute spirit with filtered or distilled water to 47% ABV. After 6 weeks, dilute again with filtered or distilled water to 44% ABV, and after 9 weeks dilute it further to 40% ABV. - Adding the water slowly during the ageing period gives the Rum a better, more rounded flavour than adding it all at once. Taste the Rum periodically during the ageing process, and it should be ready after a minimum of 2 months. The more heads and tails that were included in the blending process typically means the Rum will need to age longer. Drink and enjoy


2 comments

  • Tony Gariepy

    This post mentions 200ml foreshots containing the methanols, but the t-500 instructional videos mention 50 ml for discard. What’s the best way to KNOW I’ve removed all the methanols?

  • Andrew Walsh

    I have just purchased an Alembic Pot Still but I have been using the T-500 since 2016 with great success. I have just completed my 1st stripping run and I believe it turned out well, but I have a few questions.
    1) I could not control the pot tempture with the water flow as I can with the reflux still, is this normal?
    2) When making mashes do I still use Turbo Carbon.

    Hello from Nova Scotia Canada

Leave a comment

Please note, comments must be approved before they are published